2015. május 25., hétfő

Tila beads cube
The Japanese tila bead is entirely different from its czeh counter pair. My previous tutorial was about cubes with czeh tile beads, this one is about cubes with Japanese tila beads.
Materials
  • 9 pcs tila beads (Japanese) 
  • 48 pcs 11 sized seed beads, smaller ones are better or you can use 3  on one edge if 4 are too many 
  • 7pcs 15 sized seed beads
  • 1 piece 8 sized seed bead or a drop
Work with two needles. Weave trough both holes of the first tila bead.
String one more tila bead and sew through the first bead from back, fixing the two tila beads together, weave through them more times, until the work is tight . 
Continue in the same way, fixing together in total 5 tila beads:
Continue with the four faces of the cube. Sew 4 tila beads to 4 faces of the work. Sew using the holes of second tila of the 5 tilas row. Pass through the tilas as many times as needed to tighten the whole work and make the cube regular.
Now only the "decoration" remained.  Sew 4 pcs 11 seed beads to each edge of the cube. Firstly add 4 tilas for 4 edges which are parallel with each other, then sew 4-4 seed beads  between the already added seed beads. Fix the seed beads to both of the faces forming the actual edge.. 




At last add 7 15 sized seed beads to the corners and one 8 sized to one corner. Weave through the edges until the whole work is tight. If the seed beads are too big then use only 3 instead of 4 for one edge.
The cube is ready:

Enjoy your work!






Cube from tile beads.
Materials:

  • 6 pcs tile beads
  • 48 pcs seed beads, metallic are the best
  •  7pcs 15 seed beadfs 
  • 1 piece of  drop
I used dark thread to show you the steps better, but nylon thread is fine for it.
Start with two needles:

Weave across the two holes of one tile bead:
String three more tile beads with both needles:
Pass through all 4 tiles from back:
Pull it tight and tie a knot with the two threads.
From this point you can continue with one needle. Use alternate needles. 
Sew the remained two tiles on the bottom and top of the work:


Pull the work tight, weave trough the whole as many times as needed to tighten well. You can arrange the tiles with the needle until the cube is regular.
Sew four seed beads to each edge of the cube.  Fix the four beads to both faces of the cube.




Here you can see that the seed beads are fixed to both faces forming the edge:

Sew four seed beads between the former 8 seed beads on both sides. Now one face is surrounded by seed beads:

Continue adding the seed beads, firstly for those faces which already have four seed beads on their edge:

At last sew 15 size seed beads into 7 corners and one drop in one corner. Weave through the drop from two directions, because this will be used for hanging the cube and should be tight. You can use it for earrings or key rings.



It is ready! Enjoy it!






2015. május 20., szerda

Kocka tila gyöngyből.
A japán tila gyöngy jelentősen különbözik a cseh tile gyöngytől. Az előző leírásom a cseh tile gyöngyből készült kockáról szólt, ebben a részben a japán tila gyöngyből készült kockát fogom bemutatni.
Hozzávalók:
  • 9 db tila gyöngy
  • 11-gyes kása, a fémes a legjobb, de mindenképp kerek legyen, 48 db, a cseh fémes a jó, mert az kisebb mint a japán. 
  • 15-ös kása 7db 
  • 1 db. 8-as kása
Két tűvel dolgozunk. Átfűzzük az első tila-n a két tűt:
Utána átfűzzük a következő tilán, hozzákapcsolva az előzőhöz mindkét oldalról. Többször is menjünk át rajta,hogy szépen szorosan feküdjön egymáson a két tila. 
Ugyanígy folytatjuk, további tilákat fűzve az előzőek tetejére. Összesen 5 tilát kell jó szorosan összefűzni:
Most jön a kocka 4 oldala. Ehhez az oszlophoz 4 oldalról 1-1 tilát, tehát összesen 4-t hozzáfűzünk. Úgy kell hozzáfűzni,hogy az oszlopban lévő 2-2 második tilán menjünk mindig át. Addig kell átmenni a tilákon amíg jó szoros és szép szabályos lesz az egész:
Már csak a "díszítés" van hátra. A kocka minden élére 4-4 11-est fűzünk. Először 4 élen körbe kell menni úgy, hogy a tilákhoz fűzzük a 11-gyeseket,majd a további 11-gyeseket a már felfűzött 4-esek közé  kell fűzni. Vigyázzunk,hogy amikor a tilához rögzítjük a 11-est,akkor mindkét laphoz amivel érintkezik fűzzük hozzá. 




Végül a sarkokba befűzzük a 15-ösöket, illetve egy sarokba a 8-ast. Többször is érdemes átfűzni az éleket, addig amíg szép egyenletesen állnak az éleken a gyöngyök. Arra figyeljünk, hogy itt nagyon sok múlik a 11-gyes méretén. Ha túl nagy, akkor nem fog szépen egyenletesen állni, ezért érdemes a cseh verziót választani.
Kész is vagyunk:

Jó fűzést!